You may return most new, unopened items within 30 days of delivery for a full refund. Below is our policies in regards to returns and shipping Returns Policy We thrive to provide the best shopping experience for auto spare parts. Easy installation, no modifications needed, hardware included. All bumpers come in textured black powdercoating.
Built-in winch plate able to accomodate a 12,500 lbs winch. 120 wall tubing, high degree angles and raised corners, light tabs and solid D-ring mounts w/rings included. 3/16 inch and 1/4 inch cold rolled steel. WINCH PLATE AND ALL HARDWARE IS INCLUDED.DV8 Off Road Jeep Front Bumpers are all trail tested and proven designs. THIS IS A FULL LENGTH BUMPER THAT MATCHES THE LINES OF THE FACTORY FENDERS ON YOUR JEEP WRANGLER. Or, if from Arkansas, you can also order from a local DV8 distributor, Line-X of Searcy owned by Patrick Green, at 50. You can contact Landon or Randy from DV8-Offroad at their corporate office at 95 to place an order. DV8 Off-Road listens to their customers for any issues they encounter with their products, as well as standing behind their workmanship with a factory warranty. I n addition, the guys at DV8 Off-Road are great to work with. With instructions included and all necessary hardware (minus the screws for mounting the factory fog lights), along with a few extra hands, the FS-1 can be installed with minimal time. Its streamlined looks with the fenders gives your Jeep that “beefy” look adding protection and clearance. I have personally owned it on my rig, and have installed it on two other Jeep’s to which the owners love it. DV8 Off-Road have trail tested and have proven their designs to withstand harsh conditions yet provide functionality that we look for in a good front bumper. Manufactured with 3/16” steel, the FS-1 is a robotically welded, one-piece design to exact specifications to ensure durability in extreme conditions. Its direct bolt-on design allows for no modifications. This bumper fits all two and four door Jeep Wrangler models from 2007-2015.
Should your next aftermarket mod include a front bumper, the FS-1 Steel Series bumper is a great option. It is also important to note that the fog lights should be mounted with the adjustment screw facing down. Be sure to have some 8/32 thread x 3/4″ long machine screws with nylocks and flat washers on h and. Another note is that screws to mount the factory fog lights are not included. Other than the alignment of the studs, the installation is a breeze. However, that will be with any bumper as Jeep’s location for the canister will be in the way of any aftermarket bumper install.
There is also some struggle to put the nut on the driver side stud behind the evaporator canister. However, with an extra set of hands holding the bumper and giving tweaks of position on que, while another is using a small flathead to line the studs up, installation pains can be eased. Lining up the studs to the factory holes in the frame can be a pain. This plate is not in a fixed position, which allows for adjustment. The FS-1 is installed with eight (8) studs that are on the bumper which are welded on a steel plate (2 studs per plate). The only negative is the mounting system. Installation takes about 1-1/2 hours, which includes removal of the factory front bumper and plastic skid plate. The FS-1 is also provided with two solid mount galvanized, ¾” D-Rings to provide two tow points in the front of the vehicle. The coating was also found to repel mud, leaving no stains behind as some powder coatings do. The steel series bumpers are also provided with two-stage textured flat black powder coating to provide a strong durable finish that matches industry standards. Therefore, one can sport the bumper without a winch, eliminating that huge void as if “there should be a winch there”. The separate winch plate adds versatility for those who do not have a winch just yet. The bumper comes with a separate ¼” winch plate to accommodate up to a 12,500 lb winch, adding strength to the winch mounting base, as well as providing the base for the fairlead mounting location. In addition, the 2” tube stingers add protection for the grille as well as providing two welded light tabs for mounting additional lights. This bumper also utilizes the factory fog light which is a plus. Its ends contour and offset up to line up beneath the bottom of the front fenders to not only give a stream-lined appearance, but to also give that added clearance for a high-degree approach angle with raised corners for better entry and exit angles in extreme conditions. The DV8 Off-Road FS-1 front bumper has that “sleek” look for those wanting to maintain the full width of their factory fenders.